MAKITA 2708 MANUAL PDF

Table Saw mm (“) MODEL INSTRUCTION MANUAL SPEC I F ICATIONS 5/8″ Cutting capacities Blade diameter Arbor hole I ” (/4″) 1 N o . ENGLISH (Original instructions) INSTRUCTION MANUAL Table Saw MLT DOUBLE INSULATION IMPORTANT: Read Before Using. 1 ENGLISH. Power tool manuals and free pdf instructions. Find the user manual you need for your tools and more at ManualsOnline. Makita Saw User Manual.

Author: Maujar Kajigis
Country: Myanmar
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 10 September 2018
Pages: 180
PDF File Size: 11.20 Mb
ePub File Size: 9.84 Mb
ISBN: 282-6-20381-383-5
Downloads: 60576
Price: Free* [*Free Regsitration Required]
Uploader: Kigagul

Measure the distance A and B between the rip fence and blade. Keep cutting tools sharp and clean for better and safer performance.

Makita USA – Product Details

Never carry the tool by the cord or yank it to disconnect it from the socket. Ripping Ripping i s the lengthwise cutting of a board.

Page 21 w Chisel tooth combination saw blade For rip and cross-cut work. Remove the worn carbon brushes, insert the new ones and secure the brush holder caps. When tool is used outdoors, use only extension cords ma,ita for outdoor use. Secure with cup square neck bolts and nuts.

Tighten the hex bolts A with the provided wrench. Switch off the tool and then press in the restart button. It is safer than using your hand and it frees both hands to operate the tool. Avoid abrupt, fast feeding. After dadoing, always replace the blade guard with the spreader back manua, i t s original position on the table saw.

Makita 2708 User Manual

DO NOT allow a long board to move or shift on the table. Use only saw blades recommended by the manufacturer and which conform to EN, and observe that the riving knife must not be thicker than 2780 width of the cut by the saw blade and not thinner than the body of the blade. Keep the carbon brushes clean and free to slip in the holders.

  ALLGEMEINE AUFTRAGSBEDINGUNGEN STEUERBERATER 2012 PDF

The tool has been abused, misused or improperly maintained; alterations have been made to the tool. NOWset the saw on top of the assembled stand and secure with 4 hex bolts, flat washers and hex nuts.

Attach the auxiliary fence to the rip fence with two “C” clamps. Never perform any operation “free-hand” using only your hands to support or guide the workpiece.

Now secure the ruler-attaching hex bolt carefully. Slide table 3 1 Remove the table insert on the table. Immediately reattach the guard and riving knife after completing an operation which requires removal of the guard. Remove mqnual gauge from table.

Makita 2708 Saw User Manual

Tighten only temporarily the hex socket head bolt on the safety guide installing portion. Failure to do so may result in overtightening or insufficient tightening of the hex bolt. Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning it on. When more than one inside cutter is used, space the tips of the inside cutters equidistantly in relation to one another. Attach auxiliary fence to rip fence for cuts that run the length of the stock.

Assemble the inner flange, blade, outer flange and hex nut onto the arbor, making sure the teeth of the blade are pointing down a t the front of the table. Loosen the knob on the gauge and align to desired angle 0 to 6 0 ‘. If the rip fence is not parallel with the blade, proceed as follows: Wood Facing Rip Fence A wood facing should be used for operations when blade comes close to fence.

  KUMANOVSKI SPORAZUM PDF

Grounded, cord-connected tools intended for use on a supply circuit having a nominal rating less than volts: Avoid abrupt, fast feeds. If your grip should slip, the wrench may come off the hex nut, and your hand could strike the sharp blade edges. Inspect extension cords periodically and replace, if damaged. No loose clothing, gloves, neckties, rings, bracelets, or other jewelry to get caught in moving parts. Fasten with boltdnuts after drilling holes, but fasteners must not protrude from the face board, Featherboard The diagram shown illustrates dimensions for making a typical featherboard.

Wood Auxiliary Facing Miter Gauge To prevent long board from wobbling, fit the miter gauge with an auxiliary fence board. Avoid body contact with earthed or grounded surfaces e.

MAKITA INSTRUCTION MANUAL Pdf Download.

Do not attach or set on other types. NEVER reach behind or over the cutting tool with either hand for any reason. Hex bolts B 1. Grip the outer flange with wrench 22; loosen the hex nut with wrench 19 and remove the outer flange. Take both measurements using the tooth marked with the crayon.