View and Download Uniden BCT15 owner’s manual online. scanner radio with Trunk Tracker III and automatic scanning capabilities. BCT15 Scanner pdf. Uniden BCT15 Pdf User Manuals. View online or download Uniden BCT15 Owner’s Manual. Get support for your Uniden BCT15X Scanner at Uniden Customer Support. Corporate Info · Find Your Product Scanners BCT15X User Manual.
|Country:||Saint Kitts and Nevis|
|Published (Last):||23 March 2009|
|PDF File Size:||9.82 Mb|
|ePub File Size:||17.43 Mb|
|Price:||Free* [*Free Regsitration Required]|
Press Hold to return to the sweep.
Setting The Startup Key Notes: I-call IDs are usually 6-digit IDs ex: To toggle the attenuation for a search on or off press then 7 ATT while searching. In this case, the scanner displays each Tone-Out channel for two seconds. Set Priority conventional only. So, if you turned the scanner off in Close Call mode and turn it back on in Key-Safe mode, that’s the mode you’re stuck with. GPS Location-Based Alerts – notifies you when you are near an area you have programmed as a dangerous road, dangerous intersection, or a manhal point of interest.
Some common uses of these status bits are as follows: Rotate the scroll control until the system that has the group you want to lock or unlock appears. Performance is increased with higher transmit power, receive antenna tuned to the target band, and a low background RF level.
To select none press POL 4 times. Last Updated January 16, Scroll to the system then press the number of the group quick key s you want to enable. The ID channel ‘Groups’ stored within the trunking systems can be used with all the sites.
For trunked systems, the scanner moves to the next system after the hold time expires, the current transmission ends, and the channel delay expires. Programming System Options Reference Preset Fleet Mamual Note: Press again to unlock. At ‘ Select Key No. The red light flashes once then stays on for a weather or Bear Tracker alert.
Top Questions for Uniden BCT15X Scanner
A good application of this feature would be to set the longitude and latitude for each multi-site system transmitter as usually you can receive at least a handful in any given location. The search time changes depending on the search step size. Active IDs will appear in the display. To toggle the attenuation for a trunking site on or off Hold on the site and press then 7 Att. Then, select the system type: Although TV bands are listed, the scanner cannot decode digital TV audio.
When a location alert with a higher priority occurs, the current location alert is canceled and the scanner alerts for the location with the higher priority.
Max Priority Scan To turn the attenuation on or off for all bands p ress then 7 Att to toggle on or off.
Press then press and hold 8 Rev.
Uniden BCT15X Scanner
Refer to Auto Step Size chart to help find the bands in the menu. Set Data Skip with the setting set to on, when it receives a data signal, the scanner stops briefly on the channel, then immediately resumes scanning automatically.
Rotating will select different POI’s. For trunked systems, the scanner moves to the next system after the hold time expires, the current transmission ends, and the channel delay expires.
This setting applies to all channels in the system. Each site will have its own set of trunking frequencies and is monitored like a single system. Number of Talkgroups per Block. You typically set the front port to match the speed used to communicate with your PC default bps and the back port to the speed used to communicate with an attached GPS device default bps.
Rotating will select different Kanual. You can also assign Tone-Out to a search key. You can set the scanner so the Close Call feature checks for a Close Call hit every 2 seconds in the background while you are scanning or searching or use Close Call only mode.
UNIDEN BCT15 OWNER’S MANUAL Pdf Download.
To edit the location press E Yes. Bc15 the process of searching for active frequencies in quick search, service, custom search, Close Call search, Search and Store, or Close Call Auto Store.
Other channel attributes alerts, etc. Setting The Display Backlight To toggle the attenuation on or off for all bands p ress then 7 ATT. Majual 21 Then, by using the Clone feature or by exchanging files that you each have transferred to a computer using the Uniden Advanced Scanner Director UASD software you can install the programmed data into your scanner. Channel- a programmed frequency or talk group ID location. To select a different channel, turn the Scroll Control.
Set End Code Motorola only.